angle error的例句大全

This error is an absolute error, an angle , and it is measured in deg of rad.

这也是一个绝对错误, 可以以角度值度量.

The error of the rudder angle indicator is too large.

舵角指示器的误差太大.

The basic principles and calculating method of measuring the angle error of triple prism are presented.

本文论述了测量三垂面棱镜角度误差的基本原理和计算方法.

A error limitation of angle and chordal highness method is used to filtrate clouding point.

对大量数据的精减,利用角度和弦高的最大允许偏差法进行点云精减.

The error introduced by a finite collimation angle is a systematic one in apparent transmission.

一定准光间所带来的误差是包括在表现透光率中的一种系统误差.

Misalignment Angle Calibration between SIMU and Gun Barrel Analysis on Meting Error of Quantitative Loading Technique of LPG and Error Removal

捷联惯组与炮管之间安装误差角的标定方法液化石油气定量装车计量误差分析及预防

When The goniometer is used as spectrometer, the design of 2:1 driving mechanism of self-hunting minimal angle of deviation method is applied. Synchronous error of the driving mechanism is estimated, and the error data are given.

介绍了当仪器作为分光仪使用时，采用自寻最小偏向角法的2：1传动机构的设计，估算了传动机构的同步误差，并给出了误差数据。

The error pickoff is an angle-to-voltage transducer.

误差检测器是把角度转换为电压的传感器.

The paper proves that the error caused by the operator when adjusting cutting head angle, blade angle and grinding system will have influence on cigarette rod cutting quality;

本文分析了在调整刀盘角度、切刀角度、磨削装置过程中，由于操作者所带来的误差（测量误差）对烟支切割质量的影响；

The anticlastic curvature caused by bending is 1 700 times as long as the sagittal curvature, and the incident angle error is only 2.2 μ rad.

优化后晶体因压弯产生的鞍形曲率半径约为弧矢曲率半径的1700倍，造成的入射角误差为2.2μrad；

Analysis of orientation error of vitrified porcelain tile side-grinding and angle-cutting machine tool

瓷质墙地砖磨边倒角机定位误差分析

The adjustment of rotation angle error of power box twin export axles of twin screw extruder

双螺杆挤压机动力箱双输出轴转角误差调整

The error analysis in the measurment of a coning angle with a sine bar

用正弦规测量圆锥角实验的误差分析

The improvement of predicting error is mainly due to introduction of general normalized elevation angle function.

引入通用归一化仰角函数是改善预报误差的主要原因。

Verification O Class Plane Planeness Error Research With small Angle Instrument

小角度仪器检定0级平板平面度的误差研究二维[度]的，平面的

We find that error increases when the angle between the axis and the slice decreases.

并由此发现由于中轴线与切片交角过小会使结果产生较大偏差。

The angle only data error is treated as mini disturbance of parameters and the sensitivity analysis model ( fhp) on nonlinear programming is established in the case without disturbance.

测角观测误差看作为参数的微摄动，而非线性规划的灵敏性分析模型（fhp）建立在无摄动的情况下。